QM BenchQuality engineering tools

True Position Calculator (GD&T) with MMC / LMC Bonus

Enter the X/Y deviations of holes and pins from your CMM report and get the diametral position, the bonus tolerance at MMC or LMC and a pass / fail result for every feature.How to use ↓Full guide with case study →
  • Free, no sign-up
  • Data stays in your browser
  • PDF report included

Part ofQuality inspection

Empty template

Fill in the form below, or load the sample to see a complete example and replace it with your own data.

  1. 1Enter or paste dataor click Load sample
  2. 2Read the verdictcharts and key figures
  3. 3Download the PDFwith your logo

Features and measured deviations

deviations = actual − nominal from the CMM report, in the datum reference frame
FeatureTypePosition tol. ØModifierSize minSize maxActual sizedXdY

Actual size: the actual mating size for MMC (largest pin that fits the hole, smallest ring that fits the pin), the actual minimum material size for LMC. Size limits and actual size are needed only with MMC or LMC.

Verified calculations144/144 checks passedagainst NumPy 2.5.4 · SciPy 1.18.1 and published reference data · last run 2026-10-24Test report →
In-depth guide: theory, step by step and a worked case studyWritten by Ľubomír Blažek, process quality team leader, automotiveRead →

True position calculator with bonus tolerance

Turn the X and Y deviations from a CMM report into the diametral position value that a GD&T position callout limits, and see at once whether each feature is in tolerance. Enter several holes and pins together, for example a bolt pattern, and get a pass / fail table, a plot of every actual position inside its tolerance zone and a PDF report.

When the callout carries an MMC or LMC modifier, the calculator adds the bonus tolerance from the actual size of each feature, so parts that look out of position on the stated tolerance are not rejected by mistake.

Worked example: True Position Calculator

hole Ø10 +0.2/0, position Ø0.1 at MMC, actual size 10.12.
  1. 01Measure0.06 / 0.08dX / dY from the CMM
  2. 02PositionØ 0.202 · √(dX² + dY²)
  3. 03Bonus+ 0.12actual 10.12 − MMC 10.00
  4. 04DecideØ 0.20 ≤ 0.22 OKstated tolerance + bonus

01Method

The position value is twice the radial distance between the actual and the true position: Ø = 2 · √(dX² + dY²). With the Z option the deviation in Z is included for a spherical zone. The allowed value is the stated tolerance plus the bonus.

At MMC the bonus is how far the actual mating size has moved away from the maximum material size (a larger hole, a smaller pin). At LMC it is how far the actual minimum material size has moved away from the least material size. A feature outside its size limits is rejected and gets no bonus. The datum reference frame is taken as measured; extra tolerance from datum feature shift is not added.

02When to use it

Use it to evaluate CMM results of holes, pins and bolt patterns at first article, PPAP dimensional results, incoming inspection and when a customer reports an assembly problem. It is also a quick way to check how much bonus a feature really has before a tolerance or a rework decision.

If all features of a pattern are shifted the same way, the cause is usually common to the pattern, such as the fixture, the datum alignment or the program zero, and the calculator shows that mean shift.

PDF report in one click

Export a landscape PDF with your header (part, drawing revision, CMM program), the verdict, the full feature table with position, bonus, allowed value and result, the position plot and the tolerance-used chart.

Private: runs in your browser

All calculations run in your browser. Measured values and drawing data are not uploaded.

How to evaluate true position

  1. Read the callout: position tolerance Ø, the modifier (none, Ⓜ or Ⓛ) and the size limits of the feature.
  2. Take the deviations dX and dY (actual minus nominal) in the datum reference frame of the drawing, as the CMM report gives them.
  3. Enter the actual size for features with MMC or LMC. Without it no bonus can be credited.
  4. Read the result: position Ø, allowed Ø (tolerance plus bonus), share of the tolerance used and the margin.
  5. Look at the plot: points that scatter point to the process of single features; points that all lean the same way point to a common offset such as the fixture or the program zero.

Worked example with bonus

A hole is specified as Ø10 +0.2/0 with a position tolerance of Ø0.1 at MMC. The CMM reports dX = 0.06 and dY = 0.08. The radial deviation is √(0.06² + 0.08²) = 0.10, so the position value is Ø0.20, twice the stated tolerance. The actual mating size is 10.12. MMC of the hole is 10.00, so the bonus is 0.12 and the allowed position is Ø0.22. The hole is in tolerance with 91 % of the allowed value used. Without the MMC modifier the same hole would be rejected.

Common mistakes

  • Comparing the radial deviation (or dX and dY separately) with the diametral tolerance.
  • Taking bonus from a feature that is outside its size limits.
  • Using a two-point size instead of the actual mating size for the bonus.
  • Adding bonus to every feature for a datum feature at MMC; datum shift moves the whole pattern, not each feature.

Position errors add up in an assembly like any other dimension: check the effect on the gap with the tolerance stack-up calculator. To judge position over many parts, enter the position values in the process capability tool; position has only an upper limit, so it is a one-sided characteristic. Background: true position in the glossary.

Frequently asked questions

›Why is the position value twice the deviation?

A position tolerance in a feature control frame is the diameter of a zone around the true position. The measured deviation is a radius: the distance from the true position to the actual axis or centre. To compare it with the diameter, it is doubled: Ø = 2 · √(dX² + dY²).

›What is bonus tolerance?

With an MMC modifier the position tolerance applies when the feature is at its maximum material size, the smallest hole or the largest pin. As the actual mating size moves away from MMC, the feature has more room to fit its mating part, and that difference is added to the position tolerance. With LMC the same works from the least material size.

›Which actual size do I enter?

For MMC the actual mating size: for a hole the largest perfect cylinder that fits inside it, for a pin the smallest perfect cylinder that fits around it. For LMC the actual minimum material size. A two-point diameter can differ from these on a feature with form error, so take the value the CMM program reports for the mating envelope where it is available.

›Does the calculator include datum feature shift?

No. When a datum feature of size is referenced at MMC, the pattern may get additional shift, but only as a group and depending on the datum feature, not as a bonus per feature. That needs a datum simulation or a functional gauge, so the calculator uses the deviations as measured in the datum reference frame.

›When do I use the Z deviation?

Only for a spherical tolerance zone (SØ), for example the centre of a ball. For a hole or pin axis perpendicular to the X/Y plane the Z coordinate lies along the axis and is not part of the position value.